Announcement

Collapse
No announcement yet.

modifying a Saiga .308 into a PSL /Dragunov lookalike

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Vulcan
    replied
    Re: modifying a Saiga .308 into a PSL /Dragunov lookalike

    The Rhineland Arms stocks are nice. I had a PSL with one on it. I picked up a blemished stock set form them pretty cheap. You have to remove the front hand guard mount thing from the gas tube. Otherwise it is drop in.

    here is a link to their Saiga stock sets: http://www.troupsystems.com/saiga.htm

    Leave a comment:


  • Iowegan
    replied
    Re: modifying a Saiga .308 into a PSL /Dragunov lookalike

    I had one and sold it couple months back. PSL, that is.

    Leave a comment:


  • AKrazy
    replied
    Re: modifying a Saiga .308 into a PSL /Dragunov lookalike

    Nice to see this post back up! I've been wanting one of these "conversion kits" for my PSL from Rhineland:
    http://www.troupsystems.com/svd%20kit.htm

    The only thing that is holding me back is the poor performance of my PSL that I have been experiencing for some time now. I have very limited Saiga experience so I'm not sure if the PLL/Saiga hand guard parts are interchangeable but it would definitely get you close to the look you are trying to achieve.

    Best,

    Leave a comment:


  • kosh
    replied
    Re: modifying a Saiga .308 into a PSL /Dragunov lookalike

    Be sure to keep an eye out for the 922 parts count.

    Leave a comment:


  • ISC
    replied
    Re: modifying a Saiga .308 into a PSL /Dragunov lookalike

    I'm getting back to this project soon. I found a Romanian dragunov buttstock just like this one:


    I have the parts to move the trigger to its correct position and have a L1A1 flashider that I think is close evough to the real deal that I think it can be adapted to look good. I still need to find a forend substitute, but think my best bet might be to modify the Saiga forend.

    This is what I want it to look like as near as possible:


    This is the real deal


    This is one that someone else did:

    Leave a comment:


  • RT
    replied
    Re: modifying a Saiga .308 into a PSL /Dragunov lookalike

    Yes, I had one most of the way done when the feds raided my house and took it. I did the relocation of the trigger guard the cheap but reliable way, then was using a stock from a thumbhole WASR rifle and modifying it slightly to work on the Saiga. All said and done, the wood Saiga stock was better to begin with and was best just left alone. I still have that stock if you want it for the cost of shipping. I also have a Russian scope mount for it with a NcStar scope, as the POSP I had ordered never made it.

    Leave a comment:


  • AKrazy
    replied
    Re: modifying a Saiga .308 into a PSL /Dragunov lookalike

    Originally posted by jefferson101 View Post
    The whole thing sounds interesting to me, although I already have a whole Romak-3, which looks enough like a Dragunov to fool anyone who doesn't know a seriously large amount about them.

    Beyond that, it shoots fairly well like one for the first three rounds, until the barrel gets hot. I have serious considerations about doing a fiberglass bedding in the stock for it, just to see what happens to the accuracy on the fourth round and beyond.


    I picked up one of those Czech 7.62x54r barrels for my ongoing "Mosin Nagant Sniper Project" and I keep holding it up to my PSL and having nasty thoughts. Might work better than bedding

    Leave a comment:


  • jefferson101
    replied
    Re: modifying a Saiga .308 into a PSL /Dragunov lookalike

    The whole thing sounds interesting to me, although I already have a whole Romak-3, which looks enough like a Dragunov to fool anyone who doesn't know a seriously large amount about them.

    Beyond that, it shoots fairly well like one for the first three rounds, until the barrel gets hot. I have serious considerations about doing a fiberglass bedding in the stock for it, just to see what happens to the accuracy on the fourth round and beyond.

    Leave a comment:


  • AKrazy
    replied
    Re: modifying a Saiga .308 into a PSL /Dragunov lookalike

    I'd totally go for it ISC! It could look like one of those paratrooper PSLs that were out a few years back with the barrels cut back to the gas block. I really wanted one at the time. I'm sure you've seen them but here's a link anyway to a thread I found that had a couple of pics. They look mean all short like that!

    http://www.calguns.net/calgunforum/s...d.php?t=223792

    Visually, it would be a cool improvement over the stock Saiga look IMO.

    The more I think about it I want to do it...

    Leave a comment:


  • ISC
    replied
    Re: modifying a Saiga .308 into a PSL /Dragunov lookalike

    that's the whole thing. I have a 20" .308 saiga, I have a PSOP scupe for it that fits. I even have a synthetic Dragonov stock that I could put on it, although I think wood would look better.

    I came really close to getting a PSL about a year ago but got a .308 AR instead mostly because of the ARs caliber, but also due to the accuracy too.

    I'd like to have a Dragunov in my collection though, even if its a fake.

    Just to illustrate the point for all you purists out there, I'd love to have a Tiger tank too, even if it's just a sheet metal shell welded to a dune buggy.

    Leave a comment:


  • AKrazy
    replied
    Re: modifying a Saiga .308 into a PSL /Dragunov lookalike

    That sounds like a fun idea! Were you thinking of using the traditional PSL optics as well to make it look the part? Would the barrel stay the same?

    Leave a comment:


  • ISC
    started a topic modifying a Saiga .308 into a PSL /Dragunov lookalike

    modifying a Saiga .308 into a PSL /Dragunov lookalike

    Has anynbe tried this? I'm thinking I could just use the Romainian furniture that came on their AKs during the ban years after moving the trigger guard forward to its original position.

    922r blah blah blah
Working...
X